STEEL PIPE KNOWLEDGE & INSIGHTS

Steel Pipe Articles & Industry Insights

 FBE Coated Pipe for Water Treatment Plant Piping in Vietnam and Thailand

Inside a water treatment plant the pipe rarely runs in a straight line for more than a few metres. It turns, branches, reduces, passes through a wall, connects to a valve and drops into a sump. The diameters are moderate, the fittings are numerous, and almost everything is above ground in a building that is permanently humid. This is a different specification problem from a transmission main, and it is why FBE coated pipe rather than a three layer polyethylene system is usually the right answer for plant piping.

I. Why Plant Piping Prefers a Thin, Hard Coating

A fusion bonded epoxy coating is applied as a powder onto a heated, blasted steel surface and cures into a hard, tightly bonded film. Because it is thin and hard, it does not interfere with fitting alignment, it tolerates the dimensional tolerances of valves and couplings, and it can be applied to the internal surface as well as the external. For plant piping that is assembled from many short spools, those properties matter more than the impact resistance that a buried main needs.

熔结环氧涂层是将粉末喷涂到加热并经喷丸处理的钢管表面,固化成一层薄而结合紧密的膜。因为薄且硬,它不干扰阀门和接头的配合尺寸公差,也可以涂覆在内壁和外壁。对于由大量短段拼装而成的水厂管线,这些特性比埋地主管需要的抗冲击性更重要。

The same properties make an FBE coated pipe easier to repair in a plant: a damaged area can be prepared and patched with a compatible epoxy system and returned to service quickly, without the layer build-up that a polyolefin jacket requires.

II. Internal Coating Is a Separate Decision

Plant piping carries raw water, settled water, filtered water, backwash water, chemical solutions and sludge, and the internal environment differs by stream. A single internal coating steel pipe specification applied across the whole plant is usually wrong. The internal lining should be selected per stream: cement mortar for large raw and potable water lines, a potable-water-approved epoxy for filtered water and chemical dosing lines, and a material resistant to the specific chemical for the dosing and neutralisation areas.

Where potable water contact is involved, the approval question is local. A potable water coated pipe may require a hygienic approval or a quality declaration from the authority, and a mill test certificate does not satisfy that requirement. Ask the authority which approval applies before the lining clause is fixed.

III. Where the Coating Scope Usually Stops Too Early

A fusion bonded epoxy coated pipe system is only continuous if the weld area is coated with a compatible material and the flange outside diameter is protected after bolting. Both are small items, both are routinely omitted, and both are visible on the first inspection walk-down.

IV.Humidity, Condensation and Plant Operation

A treatment plant in Vietnam or Thailand operates in high humidity all year, and many areas are wet continuously. Condensation on coated steel is normal, and it affects two things: the adhesion of any site-applied coating, and the corrosion of any bare area. That is an argument for maximising factory-applied coating and minimising site work, not for accepting a lower-grade site system.

It is also an argument for specifying the surface preparation standard for site repairs, because a repair applied onto a damp, poorly prepared surface will disbond within a season. On plant work, the repair procedure belongs in the commissioning documentation, not in a supplier’s folder.

VI. Summary

Select the internal lining per stream, protect the fittings at the factory, and write the site repair procedure before commissioning. Youcheng supplies large-diameter plastic-coated steel pipe and cement mortar lined steel pipe alongside spiral welded steel pipe for plant work. Related: fusion bonded epoxy coating in the mill and epoxy lined pipe for treated water mains. Send the plant pipe schedule and we will separate the internal and external scope. Related reading: fusion bonded epoxy coated pipe; AWWA C210 epoxy coating; steel pipe hydrostatic test; cement mortar lined steel pipe. Related reading: fusion bonded epoxy coated pipe; AWWA C210 epoxy coating; steel pipe hydrostatic test; cement mortar lined steel pipe.

Related Articles

Scroll to Top